Dell Technologies PowerScale Maintenance (D-PSC-MN-01) Certification Sample Questions

PowerScale Maintenance Dumps, D-PSC-MN-01 Dumps, D-PSC-MN-01 PDF, PowerScale Maintenance VCE, Dell Technologies D-PSC-MN-01 VCE, Dell Technologies PowerScale Maintenance PDFThe purpose of this Sample Question Set is to provide you with information about the Dell Technologies PowerScale Maintenance exam. These sample questions will make you very familiar with both the type and the difficulty level of the questions on the D-PSC-MN-01 certification test. To get familiar with real exam environment, we suggest you try our Sample Dell Technologies PowerScale Maintenance Certification Practice Exam. This sample practice exam gives you the feeling of reality and is a clue to the questions asked in the actual Dell Technologies Certified PowerScale Maintenance certification exam.

These sample questions are simple and basic questions that represent likeness to the real Dell Technologies D-PSC-MN-01 exam questions. To assess your readiness and performance with real time scenario based questions, we suggest you prepare with our Premium Dell Technologies PowerScale Maintenance Certification Practice Exam. When you solve real time scenario based questions practically, you come across many difficulties that give you an opportunity to improve.

Dell Technologies D-PSC-MN-01 Sample Questions:

01. What are the necessary requirements for node class compatibility when adding new nodes to an existing cluster?
a) Same node series, same amount of memory installed, and same back-end NIC port speed
b) Same number of HDDs, same node model, same OneFS version above 9.0
c) Same node series, same number of HDDs, same HDD and SSD layout
d) Same OneFS version above 9.0, same back-end NIC port speed, same SED, and SSD security settings
 
02. A platform engineer is installing a fully populated Dell PowerScale Gen 6 chassis in a customer rack. However, the equipment lift is broken. What is the appropriate course of action to take before attempting to lift the chassis?
a) Remove the power supplies and hard drives, then rack the chassis.
b) Remove the power supplies and drive sleds while waiting for the lift to be repaired.
c) Stop work until the lift is repaired and fully functional.
d) Remove and label the drive sleds and compute modules, then rack the chassis with assistance.
 
03. Which network configurations are valid on a Dell PowerScale Gen 6 cluster that uses an Ethernet backend?
a) IPv6 addressing only, 1500 MTU, and 48-bit subnet mask
b) IPv4 addressing only, 9000 MTU, and 24-bit subnet mask
c) IPv4 addressing only, 1500 MTU, and 48-bit subnet mask
d) IPv4 or IPv6 addressing, 1500 MTU, and 24-bit subnet mask
 
04. According to Dell PowerScale best practices, which component may be replaced by the customer?
a) Fan
b) Battery
c) M.2 vault card
d) Power supply
 
05. What is the recommended way to install a Dell PowerScale Gen 6 compute module in a chassis?
a) Support the node with both hands and slide it into the node bay.
b) Slide the release lever to the right and guide the node into the chassis.
c) Close the module lever and slide the module into the chassis until it clicks.
d) Loosen the thumbscrew on the release lever then slide the compute module into the chassis.
 
06. Which Dell PowerScale interface is the simplest to use for customers?
a) OneFS command line
b) Platform application interface
c) Serial console
d) Web administration interface
 
07. In a Dell PowerScale Gen 6 cluster, which nodes work as a pair?
a) Nodes in slots 1 and 2
b) Nodes in slots 2 and 4
c) Nodes in slots 1 and 3
d) Nodes in slots 2 and 3
 
08. What is the maximum number of Dell PowerScale Gen 6 chassis that can be installed in a 42U rack?
a) 12
b) 8
c) 10
d) 6
 
09. How can an administrator verify that a node is successfully shut down?
a) Verify the LEDs on the front panel are not lit.
b) Execute the isi status -q command and see that the node is in a D--- status.
c) Execute the isi status -q command and see that the node is in an A-- status.
d) Try to access a share on the node and verify the share is inaccessible.
 
10. When should the customer engineer document and register a Dell PowerScale system in the install base record?
a) Before OneFS has been initialized, configured, and updated
b) Before racking the system
c) After racking the system
d) After OneFS has been initialized and configured

Answers:

Question: 01
Answer: c		 Question: 02
Answer: d		 Question: 03
Answer: b		 Question: 04
Answer: d		 Question: 05
Answer: a
Question: 06
Answer: d		 Question: 07
Answer: a		 Question: 08
Answer: c		 Question: 09
Answer: b		 Question: 10
Answer: c

Note: For any error in Dell Technologies Certified PowerScale Maintenance (D-PSC-MN-01) certification exam sample questions, please update us by writing an email on feedback@edusum.com.

Rating: 4.9 / 5 (78 votes)